Обсуждение прошивок для модемов LAN122/422/W422G

[digdream]

[digdream]

[vovanxp]

# echo "begin;connection0:pppoe:command/stop;end" | cm_cli
error: error_code=-1, err_msg=There is no container 'connection0'


Не могу понять в чем дело, почему ошибка., подскажите плз.

[Zyxmon]

vovanxp Значит у Вас connection1 или 2 или 3.

[SLOG]

После перепайки конденсаторов пропал Wi-Fi, хотя возможно и раньше - давно не пользовался.
Обновил прошивку до последней и bootloader, выполнил команды:
echo "NVS_TFTP_LOAD 0" >> /proc/ticfg/env
echo "vlynq_polarity high" >> /proc/ticfg/env
не помогло .

Модем пишет следующее:

Product Information
Model Number Sprinter@ADSL W422G
HW Revision Unknown
Serial Number none
Ethernet MAC 00:14:2B:11:6B:78
DSL Default MAC 00:14:2B:11:6B:7A
AP MAC N/A

Software Versions
Acorp Firmware V.2.06.RU.23042009
Gateway 3.7.1B
ATM Driver 6.01.03.00
DSL HAL 6.01.02.00
DSL Datapump 6.02.01.00 Annex A
SAR HAL 01.07.2c
PDSP Firmware 0.54
Wireless Firmware N/A
Wireless APDK N/A
DIE ID N/A
Boot Loader 1.4.0.5


# cat /proc/ticfg/env
ProductID Sprinter@ADSL W422G
HWRevision Unknown
SerialNumber none
mtd2 0x90000000,0x90010000
mtd3 0x90010000,0x90020000
mtd4 0x90020000,0x90400000
MAC_PORT 1
IPA 192.168.1.1
BOOTCFG m:f:"mtd1"
MEMSZ 0x01000000
FLASHSZ 0x00400000
MODETTY0 9600,n,8,1,hw
MODETTY1 9600,n,8,1,hw
PROMPT (psbl)
BUILD_OPS 0x301
IPA_SVR 192.168.1.22
CPUFREQ 211968000
MIPSFREQ 211968000
SYSFREQ 105984000
DSL_BIT_TMODE 1
DSL_UPG_DONE 1
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
HWA_0 00:14:2B:11:6B:78
HWA_3 00:14:2B:11:6B:7A
wan_br_mac 00:14:2B:11:6B:7A
WLAN_HWADDR 00:14:2B:11:6B:79
mac_ap 00:14:2B:11:6B:79
WLAN_EEPROM0 021156041B06001200000601095612000000010D56A9000000026D54A8D33FB3
WLAN_EEPROM1 60000000013984000100000101854C1068900105850600100001298507000000
WLAN_EEPROM2 01C1850000300001C585000000000111850000FFFF0115850000F0FF01A58500
WLAN_EEPROM3 8000000109850000800201010C03000000012184000000800181851D00030001
WLAN_EEPROM4 55090100000001E5580200000001F1580800000001D5581000000001B1580400
WLAN_EEPROM5 0000000000000000000C00C300FE0008011401260144014D014F0165019F01AF
WLAN_EEPROM6 01B70101390000110004010101000501060002010201021E000A000205020411
WLAN_EEPROM7 2244030610203031324004095449204143583130300507544920546573740108
WLAN_EEPROM8 1F0A88893E5C01BC0502000037007000AC00E8000404441024004510F003185A
WLAN_EEPROM9 4000145A2000020E0801BA000A013D025A00DA0185095000D0000A016B025A00
WLAN_EEPROM10 D20185090107100000400000010000050400010100000000FFFFFFFFFDFDFDFD
WLAN_EEPROM11 FBF4F4F4F40E0409090909090909090909090909090909090909090909090909
WLAN_EEPROM12 090909090909090909090909090909090909090909090909090909090909090E
WLAN_EEPROM13 0100000000000000000000000000000302A318A3180700012000000000000000
WLAN_EEPROM14 00000000000000000000000000000000000000000000000000
dspannex a
usb_vid 0x0451
usb_pid 0x6060
HWA_RNDIS 00:E0:A6:66:41:EB
HWA_HRNDIS 00:E0:A6:66:41:E1
connection1-mac 00-30-88-01-4e-91

connection0-mac 00-30-88-01-4e-91

vlynq_polarity high
mtd1 0x90020090,0x90097000
mtd0 0x90097000,0x90400000
connection1 0xf52b

bootloaderVersion 1.4.0.5
NVS_TFTP_LOAD 1
connection0 0x4919

#

Jan 1 12:00:12 cfgmgr(sar): Could not get oam_ping_interval from boot loader env
Jan 1 12:00:12 cfgmgr(sar): Trying to retreive the value from Configuration
Jan 1 12:00:12 cfgmgr(sar): oamPingInterval(20)(20)
Jan 1 12:00:12 cfgmgr(ap): AP Acquiring Lock
Jan 1 12:00:12 cfgmgr(resolver): stat successfull for /etc/resolv.conf.
Jan 1 12:00:12 cfgmgr(resolver): Resolver Polling Timer Started succesfully.
Jan 1 12:00:12 cfgmgr(sar): DSL Polling Timer Started succesfully.
Jan 1 12:00:13 cfgmgr(fdb): Firewall NAT service started
Jan 1 12:00:13 cfgmgr(ap): AP REPORT LOCK ACQUIRED
Jan 1 12:00:13 cfgmgr(ap): wlan_handle_load_event - Acquired Lock
Jan 1 12:00:13 cfgmgr(ap): MAC address : 00:14:2b:11:6b:79
Jan 1 12:00:14 cfgmgr(lanbridge0): Bridge Created: br0
Jan 1 12:00:16 cfgmgr(lanbridge1): Bridge Created: br1
Jan 1 12:00:18 cfgmgr(lanbridge2): Bridge Created: br2
Jan 1 12:00:19 cfgmgr(ap): WPA Authenticator Started
Jan 1 12:00:19 cfgmgr(lanbridge3): Bridge Created: br3
Jan 1 12:00:22 cfgmgr(lanbridge0): Bridge Interface Added: eth0
Jan 1 12:00:23 cfgmgr(lanbridge0): Bridge Interface Added: eth1
Jan 1 12:00:25 cfgmgr(lanbridge0): Bridge Interface Added: eth2
Jan 1 12:00:27 cfgmgr(lanbridge0): Bridge Interface Added: eth3
Jan 1 12:00:29 cfgmgr(ap): EEPROM len 474
Jan 1 12:00:29 cfgmgr(ap): Failed to get DIE ID from wlan driver. Cannot validate EEPROM Image
Jan 1 12:00:29 cfgmgr(ap): Error: Failed to get a valid EEPROM Image. AP is DOWN
Jan 1 12:00:29 cfgmgr(ap): NVS_TFTP_LOAD is enabled to download the correct EEPROM image during next boot.
Set TFTP Server Address using IPA_SVR env variable
Jan 1 12:00:29 cfgmgr(ap): Setting bootloader env NVS_TFTP_LOAD to 1
Jan 1 12:00:29 cfgmgr(ap): AP Releasing Lock
Jan 1 12:00:30 cfgmgr(sar): DSL Carrier is down
Jan 1 12:00:40 cfgmgr(sar): DSL Carrier is up
Jan 1 12:00:40 cfgmgr(sar): auto_vcc_default oamPing(0.35)result(2)
Jan 1 12:00:40 cfgmgr(sar): auto_vcc_default oamPing(0.32)result(2)
Jan 1 12:00:40 cfgmgr(sar): auto_vcc_default oamPing(0.40)result(2)
Jan 1 12:00:40 cfgmgr(sar): auto_vcc_default oamPing(0.36)result(2)
Jan 1 12:00:40 cfgmgr(sar): auto_vcc_default oamPing(0.38)result(2)
Jan 1 12:00:40 cfgmgr(sar): auto_vcc_default oamPing(0.96)result(2)
Jan 1 12:00:40 cfgmgr(sar): auto_vcc_search oamPing(0.35)result(2)
Jan 1 12:00:40 cfgmgr(sar): auto_vcc_search oamPing(8.35)result(2)
Jan 1 12:00:40 cfgmgr(sar): auto_vcc_search oamPing(0.43)result(2)
Jan 1 12:00:41 cfgmgr(sar): auto_vcc_search oamPing(0.51)result(2)
Jan 1 12:00:41 cfgmgr(sar): auto_vcc_search oamPing(0.59)result(2)
Jan 1 12:00:41 cfgmgr(sar): auto_vcc_search oamPing(8.43)result(2)
Jan 1 12:00:41 cfgmgr(sar): auto_vcc_search oamPing(8.51)result(2)
Jan 1 12:00:41 cfgmgr(sar): auto_vcc_search oamPing(8.59)result(2)
Jan 1 12:05:33 cfgmgr(pppoe-107): Valid Configuration Tree
Jan 1 12:05:33 cfgmgr(pppoe-107): PPPoE Apply Transaction
Jan 1 12:05:33 cfgmgr(pppoe-107): PPPoE Current State = 2
Jan 1 12:05:33 cfgmgr(pppoe-107): PPPoE Apple Code = 1
Jan 1 12:05:33 cfgmgr(pppoe-107): PPPoE ReStart Flag = 0
Jan 1 12:05:33 cfgmgr(pppoe-107): PPPoE Relaunch = 0
Jan 1 12:05:33 cfgmgr(pppoe-107): PPPoE Apply Message
Jan 1 12:05:33 cfgmgr(pppoe-107): PPPoE Current State = 2
Jan 1 12:05:33 cfgmgr(pppoe-107): PPPoE Relaunch Flag = 0
Jan 1 12:05:33 cfgmgr(pppoe-107): PPPoE AFTER Apply Transaction
Jan 1 12:05:33 cfgmgr(pppoe-107): PPPoE Current State = 2
Jan 1 12:05:33 cfgmgr(pppoe-107): PPPoE Apple Code = 0
Jan 1 12:05:33 cfgmgr(pppoe-107): PPPoE ReStart Flag = 0
Jan 1 12:05:33 cfgmgr(pppoe-107): PPPoE Relaunch = 0
Jan 1 12:05:33 cfgmgr(pppoe-107): RE-PPPoE Timer Apply...
Jan 1 12:05:36 pppd[315]: pppd 2.4.4 started by root, uid 0
Jan 1 12:05:36 cfgmgr(pppoe-107): New PPP_ID: 0x4919
Jan 1 12:05:36 cfgmgr(pppoe-107): Received pppoe server mac: 0x00-30-88-01-4e-91
Jan 1 12:05:36 pppd[315]: Got connection: 4919
Jan 1 12:05:36 pppd[315]: Saved Session ID: 0
Jan 1 12:05:36 pppd[315]: AC MAC address: 00-30-88-01-4e-91
Jan 1 12:05:36 pppd[315]: Connect: ppp0 {--} nas0
Jan 1 12:05:36 pppd[315]: CHAP authentication succeeded
Jan 1 12:05:36 cfgmgr(pppoe-107): PPPoE Connect with IP Address 91.77.158.189
Jan 1 12:05:37 cfgmgr(pppoe-107): PPPoE Connection Successfully Established
Jan 1 12:05:37 cfgmgr(pppoe-107): Renew PPPoE Session ID: 0x4919
Jan 1 12:05:37 cfgmgr(pppoe-107): sys_send_event - pppoe up
Jan 1 12:05:37 cfgmgr(pppoe-107): PPPoE Connect with Gateway IP Address: 91.77.156.1
Jan 1 12:05:37 pppd[315]: local IP address 91.77.158.189
Jan 1 12:05:37 pppd[315]: remote IP address 91.77.156.1
Jan 1 12:05:37 pppd[315]: primary DNS address 195.34.32.116
Jan 1 12:05:37 pppd[315]: secondary DNS address 212.188.4.10
Jan 1 12:05:37 syslog: dproxy force reload config.
Jan 1 12:05:57 cfgmgr(logic): Saving on Apply
Jan 1 12:06:01 cfgmgr(logic): Saving on Apply
Jan 1 12:06:03 cfgmgr(ap): Restarting AP.....
Jan 1 12:06:03 cfgmgr(ap): TERMINATE AP CALLED.........
Jan 1 12:06:31 pc: Lost SIGCHLD, process rmmod(1105) died
Jan 1 12:06:31 cfgmgr(ap): AP Acquiring Lock
Jan 1 12:06:31 cfgmgr(ap): AP REPORT LOCK ACQUIRED
Jan 1 12:06:31 cfgmgr(ap): wlan_handle_load_event - Acquired Lock
Jan 1 12:06:31 cfgmgr(ap): MAC address : 00:14:2b:11:6b:79
Jan 1 12:06:32 cfgmgr(ap): WPA Authenticator Started
Jan 1 12:06:36 cfgmgr(ap): Failed to get DIE ID from wlan driver. Cannot validate EEPROM Image
Jan 1 12:06:36 cfgmgr(ap): Error: Failed to get a valid EEPROM Image. AP is DOWN
Jan 1 12:06:36 cfgmgr(ap): NVS_TFTP_LOAD is enabled to download the correct EEPROM image
during next boot. Set TFTP Server Address using IPA_SVR env variable
Jan 1 12:06:36 cfgmgr(ap): Setting bootloader env NVS_TFTP_LOAD to 1
Jan 1 12:06:36 cfgmgr(ap): AP Releasing Lock
Jan 1 12:06:37 cfgmgr(logic): UDP connections reset...
Jan 1 12:06:47 cfgmgr(logic): UDP connections flush...
Jan 1 12:25:39 cfgmgr(ap): ERROR:Unable to open /proc/wlan/hal/fwVer
Jan 1 12:25:39 cfgmgr(ap): ERROR:Unable to open /proc/wlan/production/version
Jan 1 12:25:39 cfgmgr(ap): ERROR: Failed to get DIE ID from wlan driver.
Jan 1 12:29:37 cfgmgr(ap): ERROR:Unable to open /proc/wlan/hal/fwVer
Jan 1 12:29:37 cfgmgr(ap): ERROR:Unable to open /proc/wlan/production/version
Jan 1 12:29:37 cfgmgr(ap): ERROR: Failed to get DIE ID from wlan driver.

Возможно подлечить Wi-Fi? Если не туда запостил, извините - так и не понял надо-ли заводить новую тему.

[Pooh]

TO SLOG:Тут типа всё описано http://www.ddixlab.ru/forum/viewtopic.php?t=383

# echo "NVS_TFTP_LOAD 0" > /proc/ticfg/env
# echo "NVS_DEFAULT 1" > /proc/ticfg/env
# reboot

[SLOG]

Пробовал - не помогает. После перезагрузки на шесть-семь секунд загорается индикатор Wi-Fi, затем гаснет. Wi-Fi соответственно не работает.

Посмотрел, что написано на Wi-Fi модуле:

XG-652, H/W: V0.4 NVS: 6.07
Mac: 0060B33FD3A8 S/N: XG6527AN001218

Серийник модема модема: 71000081100307

А это нормально, что мас на наклейке карты Wi-Fi (0060B33FD3A8) не соответствует мас'у из ENV (00:14:2B:11:6B:79)?

Вот лог загрузки - по-моему ничего не поменялось:

Jan 1 12:00:12 cfgmgr(sar): Could not get oam_ping_interval from boot loader env
Jan 1 12:00:12 cfgmgr(sar): Trying to retreive the value from Configuration
Jan 1 12:00:12 cfgmgr(sar): oamPingInterval(20)(20)
Jan 1 12:00:12 cfgmgr(ap): AP Acquiring Lock
Jan 1 12:00:12 cfgmgr(pppoe-107): Valid Configuration Tree
Jan 1 12:00:12 cfgmgr(resolver): stat successfull for /etc/resolv.conf.
Jan 1 12:00:12 cfgmgr(resolver): Resolver Polling Timer Started succesfully.
Jan 1 12:00:12 cfgmgr(sar): DSL Polling Timer Started succesfully.
Jan 1 12:00:13 cfgmgr(fdb): Firewall NAT service started
Jan 1 12:00:13 cfgmgr(ap): AP REPORT LOCK ACQUIRED
Jan 1 12:00:13 cfgmgr(ap): wlan_handle_load_event - Acquired Lock
Jan 1 12:00:13 cfgmgr(ap): MAC address : 00:14:2b:11:6b:79
Jan 1 12:00:14 cfgmgr(pppoe-107): del_iptable_rules : ppp_name not intact
Jan 1 12:00:14 cfgmgr(lanbridge0): Bridge Created: br0
Jan 1 12:00:16 cfgmgr(lanbridge1): Bridge Created: br1
Jan 1 12:00:18 cfgmgr(ap): WPA Authenticator Started
Jan 1 12:00:18 cfgmgr(lanbridge2): Bridge Created: br2
Jan 1 12:00:20 cfgmgr(lanbridge3): Bridge Created: br3
Jan 1 12:00:22 cfgmgr(lanbridge0): Bridge Interface Added: eth0
Jan 1 12:00:24 cfgmgr(lanbridge0): Bridge Interface Added: eth1
Jan 1 12:00:26 cfgmgr(lanbridge0): Bridge Interface Added: eth2
Jan 1 12:00:27 cfgmgr(lanbridge0): Bridge Interface Added: eth3
Jan 1 12:00:29 cfgmgr(ap): EEPROM len 474
Jan 1 12:00:29 cfgmgr(ap): Failed to get DIE ID from wlan driver. Cannot validate EEPROM Image
Jan 1 12:00:29 cfgmgr(ap): Error: Failed to get a valid EEPROM Image. AP is DOWN
Jan 1 12:00:29 cfgmgr(ap): NVS_TFTP_LOAD is enabled to download the correct EEPROM image during next boot. Set TFTP Server Address using IPA_SVR env variable
Jan 1 12:00:29 cfgmgr(ap): Setting bootloader env NVS_TFTP_LOAD to 1
Jan 1 12:00:29 cfgmgr(ap): AP Releasing Lock
Jan 1 12:00:31 cfgmgr(sar): DSL Carrier is down
Jan 1 12:00:31 cfgmgr(pppoe-107): del_iptable_rules : ppp_name not intact
Jan 1 12:00:41 cfgmgr(sar): DSL Carrier is up
Jan 1 12:00:41 cfgmgr(sar): auto_vcc_default oamPing(0.35)result(2)
Jan 1 12:00:41 cfgmgr(sar): auto_vcc_default oamPing(0.32)result(2)
Jan 1 12:00:41 cfgmgr(sar): auto_vcc_default oamPing(0.40)result(2)
Jan 1 12:00:41 cfgmgr(sar): auto_vcc_default oamPing(0.36)result(2)
Jan 1 12:00:41 cfgmgr(sar): auto_vcc_default oamPing(0.38)result(2)
Jan 1 12:00:41 cfgmgr(sar): auto_vcc_default oamPing(0.96)result(2)
Jan 1 12:00:41 cfgmgr(sar): auto_vcc_search oamPing(0.35)result(2)
Jan 1 12:00:41 cfgmgr(sar): auto_vcc_search oamPing(8.35)result(2)
Jan 1 12:00:42 cfgmgr(sar): auto_vcc_search oamPing(0.43)result(2)
Jan 1 12:00:42 cfgmgr(sar): auto_vcc_search oamPing(0.51)result(2)
Jan 1 12:00:42 cfgmgr(sar): auto_vcc_search oamPing(0.59)result(2)
Jan 1 12:00:42 cfgmgr(sar): auto_vcc_search oamPing(8.43)result(2)
Jan 1 12:00:42 cfgmgr(sar): auto_vcc_search oamPing(8.51)result(2)
Jan 1 12:00:42 cfgmgr(sar): auto_vcc_search oamPing(8.59)result(2)
Jan 1 12:00:43 cfgmgr(pppoe-107): Max Connection Delay 60
Jan 1 12:00:43 cfgmgr(pppoe-107): Conn Delay Timer started for 16 sec
Jan 1 12:00:59 cfgmgr(pppoe-107): PPPoE Launch after conn delay timeout ...
Jan 1 12:01:01 pppd[268]: pppd 2.4.4 started by root, uid 0
Jan 1 12:01:01 pppd[268]: Sending PADT for 7920 before starting new discovery
Jan 1 12:01:01 pppd[268]: Server MAC is: 00-30-88-01-4e-91
Jan 1 12:01:01 pppd[268]: Got connection: 7d2a
Jan 1 12:01:01 cfgmgr(pppoe-107): Saving PPPoE Session ID: 0x7d2a
Jan 1 12:01:01 cfgmgr(pppoe-107): Received pppoe server mac: 0x00-30-88-01-4e-91
Jan 1 12:01:01 pppd[268]: Saved Session ID: 0
Jan 1 12:01:01 pppd[268]: AC MAC address: 00-30-88-01-4e-91
Jan 1 12:01:01 pppd[268]: Connect: ppp0 {--} nas0
Jan 1 12:01:01 pppd[268]: CHAP authentication succeeded
Jan 1 12:01:02 pppd[268]: local IP address 91.78.239.30
Jan 1 12:01:02 pppd[268]: remote IP address 91.78.236.1
Jan 1 12:01:02 pppd[268]: primary DNS address 195.34.32.116
Jan 1 12:01:02 pppd[268]: secondary DNS address 212.188.4.10
Jan 1 12:01:02 cfgmgr(pppoe-107): PPPoE Connect with IP Address 91.78.239.30
Jan 1 12:01:02 cfgmgr(pppoe-107): PPPoE Connection Successfully Established
Jan 1 12:01:02 cfgmgr(pppoe-107): sys_send_event - pppoe up
Jan 1 12:01:02 cfgmgr(pppoe-107): PPPoE Connect with Gateway IP Address: 91.78.236.1
Jan 1 12:01:02 syslog: dproxy force reload config.
Jan 1 12:02:02 cfgmgr(logic): UDP connections reset...
Jan 1 12:02:12 cfgmgr(logic): UDP connections flush...
Jan 1 12:03:24 cfgmgr(ap): ERROR:Unable to open /proc/wlan/hal/fwVer
Jan 1 12:03:24 cfgmgr(ap): ERROR:Unable to open /proc/wlan/production/version
Jan 1 12:03:24 cfgmgr(ap): ERROR: Failed to get DIE ID from wlan driver.

[Darkon]

попробуйте еще раз 2.06 залить в модем.

[SLOG]

Попробовал - даже два раза для верности. Не работает Wi-Fi.
Ещё раз выполнил команды:
echo "NVS_TFTP_LOAD 0" > /proc/ticfg/env
echo "NVS_DEFAULT 1" > /proc/ticfg/env
reboot
Не помогло.

Лог практически без изменений. Попробовал снять лог Router Upgrade Check'ом, на 32% пишет: "Unable to extract the current config from the MTD3 file. Please ensure you have saved your routers config before running the Router Upgrade Check." А в конце ругается на выключенный Wi-Fi.

И вот ещё, отсутствие в логе
/proc/wlan
cd: can't cd to /proc/wlan

И пустота в
/usr/sbin/wlan

так и должно быть?

Ещё вот что вспомнил, перед перепайкой давал роутер поюзать родственнику, обратно отдали уже дохлый. А после перепайки, когда роутер ожил, то не обнаружил в WEB-интерфейсе закладку "Wireless" - разбираться не стал - сразу влил последнюю прошивку. Возможно родственник залил по-глупости прошивку от 122-го или 422-го. Сам он уже не помнит - но говорит, что чем-то перепрошивал, редиска!

Вот лог:

Router Upgrade Check 1.3.9 31.05.2010 22:39:01
Router IP: 192.168.1.1
Description: Acorp W422G
Board type: AR7WRD
Product ID: Sprinter@ADSL
Bootloader: psbl
RAM 16,0 MB
Flash (ROM) 4,0 MB
ADAM2: No
No default env: No
Linux version: 2.4.17_mvl21-malta-mips_fp_le
Firmware build: 090302
Firmware version: 3.7.1B
Firmware stamp: 20090302121314
CPU: MIPS 4KEc V4.8
DSP: 6.02.01.00
Annex: A
/proc/wlan: No
/usr/sbin/wlan: Yes
TIAP: No
TNETW: No
Wireless: Yes
WIFI chip: Not TNETW1130
WIFI chip conf: No
Ports: 4
Ports (according to router): N/A
Marvell (or Marvell like): Yes
NSP: 3.7.1B
Manufacturers: Edata Communication Inc, Siara Systems Inc
RNDIS: Telogy Networks Inc
HRNDIS: Telogy Networks Inc
WARNING
Cannot confirm the model number of the wireless chip.
The wireless access point (AP) may be disabled - ensure it is enabled and then run this program again.

Select an AR7WRD PSPBOOT 4 PORT firmware.
Latest: routertech-ar7wrd-pspboot-firmware-20100408.zip
Please read the instructions that come with the firmware files before you upgrade.
According to your current MTD values, you should be able to upgrade using a single firmware image.

/etc /versions
VERSION=3.7.1B
BUILD=090302
BOARD=AR7WRD
FSSTAMP=20090302121314
#
/proc/wlan
cd: can't cd to /proc/wlan
#
/usr/sbin/wlan
#
/proc/ticfg/env
ProductID Sprinter@ADSL W422G
HWRevision Unknown
SerialNumber none
mtd2 0x90000000,0x90010000
mtd3 0x90010000,0x90020000
mtd4 0x90020000,0x90400000
MAC_PORT 1
IPA 192.168.1.1
BOOTCFG m:f:"mtd1"
MEMSZ 0x01000000
FLASHSZ 0x00400000
MODETTY0 9600,n,8,1,hw
MODETTY1 9600,n,8,1,hw
PROMPT (psbl)
BUILD_OPS 0x301
IPA_SVR 192.168.1.22
CPUFREQ 211968000
MIPSFREQ 211968000
SYSFREQ 105984000
DSL_BIT_TMODE 1
DSL_UPG_DONE 1
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
HWA_0 00:14:2B:11:6B:78
HWA_3 00:14:2B:11:6B:7A
wan_br_mac 00:14:2B:11:6B:7A
WLAN_HWADDR 00:14:2B:11:6B:79
mac_ap 00:14:2B:11:6B:79
WLAN_EEPROM0 021156041B06001200000601095612000000010D56A9000000026D54A8D33FB3
WLAN_EEPROM1 60000000013984000100000101854C1068900105850600100001298507000000
WLAN_EEPROM2 01C1850000300001C585000000000111850000FFFF0115850000F0FF01A58500
WLAN_EEPROM3 8000000109850000800201010C03000000012184000000800181851D00030001
WLAN_EEPROM4 55090100000001E5580200000001F1580800000001D5581000000001B1580400
WLAN_EEPROM5 0000000000000000000C00C300FE0008011401260144014D014F0165019F01AF
WLAN_EEPROM6 01B70101390000110004010101000501060002010201021E000A000205020411
WLAN_EEPROM7 2244030610203031324004095449204143583130300507544920546573740108
WLAN_EEPROM8 1F0A88893E5C01BC0502000037007000AC00E8000404441024004510F003185A
WLAN_EEPROM9 4000145A2000020E0801BA000A013D025A00DA0185095000D0000A016B025A00
WLAN_EEPROM10 D20185090107100000400000010000050400010100000000FFFFFFFFFDFDFDFD
WLAN_EEPROM11 FBF4F4F4F40E0409090909090909090909090909090909090909090909090909
WLAN_EEPROM12 090909090909090909090909090909090909090909090909090909090909090E
WLAN_EEPROM13 0100000000000000000000000000000302A318A3180700012000000000000000
WLAN_EEPROM14 00000000000000000000000000000000000000000000000000
dspannex a
usb_vid 0x0451
usb_pid 0x6060
HWA_RNDIS 00:E0:A6:66:41:EB
HWA_HRNDIS 00:E0:A6:66:41:E1
connection1-mac 00-30-88-01-4e-91
vlynq_polarity high
connection1 0xf52b
bootloaderVersion 1.4.0.5
NVS_DEFAULT 1
connection0-mac 00-30-88-01-4e-91
connection2 0xe206
mtd1 0x90020090,0x90097000
mtd0 0x90097000,0x90400000
NVS_TFTP_LOAD 1
connection0 0xaa0a
#
/proc/sys/dev/adam2/environment
cat: /proc/sys/dev/adam2/environment: No such file or directory
#
/proc/version
Linux version 2.4.17_mvl21-malta-mips_fp_le (andrey@co5.local) (gcc version 2.95.3 20010315 (release/Acorp)) #1 Tue Apr 21 09:02:42 MSD 2009
#
/proc/cpuinfo
processor : 0
cpu model : MIPS 4KEc V4.8
BogoMIPS : 211.35
wait instruction : no
microsecond timers : yes
extra interrupt vector : yes
hardware watchpoint : yes
VCED exceptions : not available
VCEI exceptions : not available
#
/proc/avalanche/avsar_ver
ATM Driver version:[6.01.03.00]
DSL HAL version: [6.01.02.00]
DSP Datapump version: [6.02.01.00] Annex A
SAR HAL version: [01.07.2c]
PDSP Firmware version:[0.54]
Chipset ID: [Ohio250(7200/7100A2)]
#
/proc/interrupts
7: 40669 R4000 timer/counter [MIPS interrupt]
8: 0 unified secondary [hw0 (Avalanche Primary)]
15: 36 serial [hw0 (Avalanche Primary)]
23: 356 + SAR [hw0 (Avalanche Primary)]
27: 726 + Cpmac Driver [hw0 (Avalanche Primary)]
31: 66 + DSL [hw0 (Avalanche Primary)]
#
/proc/modules
tiatm 134400 c0020060 96 1
#
/proc/flashinfo
cat: /proc/flashinfo: No such file or directory
#
/etc/PORTS
cat: /etc/PORTS: No such file or directory
#
logic:status/nspver
3.7.1B

logic:status/has_marvell
1

/etc /led.conf
#################################################################
# Configuration File for AR7WRD board
##################################################################
module = adsl # module = {adsl,usb,pppoe}
##################################################################
# Note: state 0 for adsl is dummy state and is present only for ##
# compatibility with the new LED driver ##
##################################################################
state = 0 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = LED1 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = LED1 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = LED1 # gpio number
mode = 4 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 200 # flash on duration in ms
param2 = 200 # flash off duration in ms
state = 3 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = LED1 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 4 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = LED1 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
######################################################################
module = usb # module = {adsl,usb,pppoe,wlan}
state = 0 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
state = 3 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
######################################################################
module = pppoe # module = {adsl,usb,pppoe,wlan}
state = 0 # 0 = pppoe down, 1 = pppoe active
gpio = 13 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = pppoe down, 1 = pppoe active
gpio = 13 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
######################################################################
module = wlan # module = {adsl,usb,pppoe,wlan}
state = 0 # 0 = link down, 1 = link up
gpio = 6 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = link down, 1 = link up
gpio = 6 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 6 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
state = 3 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 6 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms

[BomG]

Люди! кто может помочь? уже второй модем w422g. первый после года работы стал зависать (т.е. лампа адсл люто моргает, в инете еле еле кое как сайты грузит какое то время - потом и ето не делает, в интерфейс не входит) я его и так и эдак - довел так что я его об пол раздолбал
Купил такой же новый в том году... и вот опять то-же самое... а другие модемы не хочу - акорп мне нравится. может каак то лечится?

[Pooh]

[BomG]

[Zyxmon]

[Zyxmon]

[Evg71]

Помогите найти образ flash для ACORP W422G ver.2.0
Программатор есть, а образа нет. Мне легче целиком FLASH прошить...
Или хотя бы загрузчик найти.

[djserg-minyar]

Добрый день всем, ребята слушайте выручайте, есть небольшая задачка:

Есть модем Acorp W422G, раньше стоял и инет по АДСЛ раздавал, пока не решил сменить провайдера, ввиду переезда, а тут только кабельный инет, договорился с провайдером, что даст статический IP и авторизатор отключит.
Так вот подскажите может можно как то этот модем настроить, так чтобы он раздавал инет от кабельного провайдера???

пробовал настраивать так:

в первую лан группу добавил только интерфейс lan1, соответственно прописал туда IP маску и гейт, которые провайдер выдал.
во вторую лан группу добавил остальные порты, и wifi, соответственно там прописал DCHP, и default роутером назначал IP, который прописывал в первой Лан группе.

Что имеем, IP адрес который прописан в первой лан группы пингуеться, роутер прова нет, и соответственно инета нет.

Может что не так делаю, и воозможно ли вообще такое реализовать на данном модеме?

[abdula]

Может кто подскажет как победить глюк в прошивке связанный с ненормальной работай Dynamic DNS Client, конкретнее клиент после установления интернет соединения не отсылает свой ip. Если принудительно применить настройки клиента в модеме все отрабатывает нормально. Может кто сталкивался с данной проблемой?

[abdula]

[Pooh]

[abdula]